Short answer
Before cleanup begins, check ten risks. A machine could start up from stored energy. People could be exposed to bloodborne germs. There may be sharp edges and fine metal bits, reactions with process chemicals, and bad air in confined spaces. Add slippery floors, electrical dangers, fire risk in flammable areas, damaged structures or hanging loads, and the strain on coworkers. A joint check with your safety and maintenance staff prevents most second injuries.
Why the cleanup brings risks the first accident did not
After a workplace injury, your mind goes to the injured worker and to what caused the accident. It is easy to forget that the cleanup is a safety concern too. Yet it often puts people in the same dangerous spot. Sometimes the guards are off and the equipment is partly taken apart.
A cleanup crew also brings new dangers with it: cleaning chemicals, water, pressure equipment and extension cords. These can combine with your plant's own dangers in ways that are easy to miss when everyone is eager to restart production.
The surest way to prevent a second accident is a joint risk check before work begins. Bring together your safety manager, your maintenance lead and the cleanup company. The ten risks below give you a practical place to start.
Fit them to your own site. A food plant, a foundry, a chemical blender and a distribution center will each weigh these risks differently.
Time pressure makes all ten worse. When your line is down and customers are waiting, people are tempted to skip a lockout step. They reach in without checking for sharp edges, or they grab the nearest chemical. Name that pressure out loud during the joint check. Agree that the safety steps are not optional. That helps everyone hold firm.
Risk 1: stored energy and a machine that starts up
Risk 1 is a machine that starts up or lets go of stored energy without warning. A machine involved in an injury often still holds energy after it stops. There may be pressure in hydraulic and air lines, or tension in springs and belts. A ram may be raised or a load may be hanging. A flywheel may be turning, or a capacitor may hold a charge. A crew that reaches inside your press or conveyor to clean off blood faces the same danger that may have caused the first injury.
Contact with objects and equipment is already a leading cause of serious injury. The numbers are large. It caused an annualized 860,050 days-away, restricted or transfer cases in private industry in 2023-24, a rate of 40.6 per 10,000 workers, according to the Bureau of Labor Statistics. That is why this risk comes first on your list.
Before anyone begins, your site's authorized employees should put on lockout and tagout, release or block the stored energy, and confirm zero energy. If your program requires it, each cleanup worker adds a personal lock. No one should ever bypass a lock or work around one.
If the accident damaged the machine, check with extra care that the power is truly cut off. Damaged valves, switches and gauges may not act the way you expect.
Risk 2: exposure to bloodborne germs
Risk 2 is exposure to germs carried in blood. Blood and tissue at an injury scene may carry bloodborne viruses. Contact can happen through a cut, a splash to the eyes or mouth, or a dirty tool. Anyone cleaning needs fluid-resistant protective clothing, gloves, and eye and face protection. Workers covered by your bloodborne germs program should already have been offered the vaccine and training.
Risk 3: cuts from sharp edges and fine metal bits
Risk 3 is cuts from sharp edges and fine metal bits. A plant scene often has sharp tooling, broken guards, stamped parts and tiny metal particles mixed into the fluids. Standard nitrile gloves tear easily in those conditions. A tear can turn a cut into a blood exposure.
Where there are sharp hazards, a good crew wears cut-resistant gloves under or over its fluid-resistant gloves. It uses tools to remove debris and keeps a hard-sided container on hand for sharp waste.
Watch out for hands inside machines. Pinch points, blades and edges are often out of sight.
Risk 4: reactions with your process chemicals
Risk 4 is a reaction with process chemicals. Your plant may store and use acids, caustics, oxidizers, solvents and reactive materials. A disinfectant or degreaser brought near those chemicals can react and give off heat or toxic gas. Chlorine-based products, for example, can release chlorine gas when mixed with acids.
Exposure to harmful substances or environments caused 820 U.S. worker deaths in 2023, falling to 687 in 2024, according to the Bureau of Labor Statistics. Before work begins, go over the safety data sheets for the chemicals near the scene and for every cleaning product. Keep materials that should not meet apart.
Risk 5: bad air in confined spaces
Risk 5 is dangerous air in a confined space. Your pits, tanks, vaults and machine enclosures can hold low oxygen, flammable vapors or toxic gases. Cleaning chemicals can make those conditions worse.
Follow your site's steps for confined spaces that need a permit. Test the air before anyone goes in, and keep testing the whole time. Bring fresh air into the space. Post an attendant outside, and have a rescue plan ready.
Risks 6 and 7: slippery floors and electrical dangers
Risk 6 is slips and falls on a dirty floor. Blood mixed with oil, coolant or hydraulic fluid makes a floor very slippery. Adding water and detergent during cleanup makes it worse. Soak up the bulk of the fluid with absorbents first. Make sure people wear slip-resistant footwear. Mark wet areas and limit foot traffic.
Risk 7 is electrical danger. Cleanup brings water near your motors, control panels, junction boxes and extension cords. Damaged equipment may have bare wiring. Cut the power and lock out the electrical systems in the work area. Use ground-fault protection on portable tools. Keep sprayed water out of electrical boxes.
Risk 8: fire where vapors or dust can burn
Risk 8 is fire or explosion where the air holds flammable vapors or dust that can burn. Some of your areas may have these. Ordinary lights, vacuums and power tools can set them off. Fires and explosions caused 104 fatal work injuries in the United States in 2023 and 93 in 2024, according to the Bureau of Labor Statistics.
Confirm whether your work area is a classified hazardous location. If it is, allow only equipment rated for it. Keep flammable cleaning products away from sparks, flames and heat.
Risks 9 and 10: damaged structures and emotional strain
Risk 9 is damaged structures and hanging loads. The accident may have damaged your racking, mezzanines, guardrails, overhead conveyors or cranes. Loads may be hanging or stacked unsafely. Anyone working under or next to a weakened structure is at risk if something shifts. Have your maintenance or engineering staff inspect and secure structures before cleanup starts.
Risk 10 is emotional strain on your coworkers and cleanup staff. Employees who saw the accident, gave first aid or knew the injured worker may be deeply affected. Asking them to clean the scene can make it worse. It also raises the chance of mistakes.
Give the cleanup to trained staff who were not directly involved, or to an outside company. Offer your employee assistance program to the workers who were affected. If the event was a death by suicide, share information about the 988 Suicide and Crisis Lifeline. It can be reached by call or text.
Ask your supervisors to watch for signs that someone is struggling in the days after the accident, not only on the day itself.
A nine-point checklist before cleanup
A written checklist keeps your joint review on track and the same on every shift.
- Have investigators and your site's safety lead released the scene?
- Is all energy cut off, locked out and confirmed at zero?
- Have sharp edges, tooling and fine metal bits been found and noted?
- Have you reviewed the safety data sheets for nearby chemicals and the cleaning products?
- Does the work involve a confined space, and is a permit in place?
- Is the area a classified hazardous location, and is the equipment rated for it?
- Is electrical power off where water will be used?
- Have structures, racking and overhead loads been inspected and secured?
- Are the people doing the work trained, equipped and not directly affected by the event?
How to lower these risks before an accident happens
You can do much of this work ahead of time. Map where your hazardous chemicals, confined spaces and classified areas are. Keep your safety data sheets up to date and easy to find. Train the employees covered by your bloodborne germs program. Stock your spill kits with cut-resistant gloves and absorbents that suit both oils and body fluids.
Find a cleanup company with plant experience and walk its people through your site before you need them. Agree on how the joint risk check will work.
After each accident, look back at how the cleanup went. Note any near misses, missing supplies or mix-ups about who was responsible. Then update your checklist. Each review makes your next response safer and faster.
Also ask your OSHA area office whether your state runs its own workplace safety plan. A state plan may add rules for lockout, confined spaces or bloodborne germs.



